Daedong Kioti RX6020 Manual Download Page 81

Page: 81 / 262

description oF operating system

TuRN SIGNAl lIGhT SwITCh

(1) turn signal light switch

(a) right turn

(b) left turn

the turn signal lights are used when

turning the vehicle left or right. pull-

ing the lever up blinks the right turn

signal light while pushing the lever

down blinks the left turn signal light.

(1) horn switch

the horn switch can be operated

without the key inserted. pressing

this switch sounds the horn.

hORN SwITCh

hAzARD lAMP SwITCh

(1) hazard lamp switch

(a) on

(b) oFF

the turn signal light lever is not

the self-return type. therefore,

make sure to return the lever

manually after turning the vehicle.
the turn signal lamps can be op-

erated without the key inserted.

•

NOTE

this switch can be used to warn

other vehicles when malfunction oc-

curs in the tractor while driving on a

public road. pressing this switch up

blinks the hazard lamp and returning

it turns off the lamp. the turn signal

lights cannot be operated while this

switch is pressed up to operate the

hazard lamps.

T11O406A

T11O407A

M55O4A2A

TF110(RX7320)ROPS합본-US,EU,AU-04.9 9

2016-06-07 오후 7:17:20

Summary of Contents for Kioti RX6020







































































































































































































































































Search results

Summary of Contents for Kioti RX6020

Reviews:

Daedong Kioti RX6020, Manual, Page: 81 / 262

Search results

Summary of Contents for Kioti RX6020

Reviews: