Daedong Kioti RX6020 Manual Download

Page: 99 / 262

description oF operating system

this switch is to settle the revolution

of pto. when you push down the

button of set(-) while turn the pto

cruise button on, this lamp turn on.

CRuISE PTO wARNING lAMP

T11O488A

bRAKE (ONE SIDE) lAMP

(1) brake pedal lock (both sides)

M55O4L4A

T11O489A

this lamp indicates the operating

status of the brake (one side). this

comes on when the brake lock for

two brake pedals is unlocked.

when driving on a public road

or at a high speed, never use

only one brake pedal. The

tractor can roll over.
while the brake (one side)

lamp is illuminated, the brake

pedals are not interlocked and

only one brake pedal can be

depressed accidentally. Make

sure to set the pedal lock to the

"lock" position in a normal

condition.

•

IMPORTANT

TF110(RX7320)ROPS합본-US,EU,AU-04.27 27

2016-06-07 오후 7:17:32

Summary of Contents for Kioti RX6020







































































































































































































































































Search results

Summary of Contents for Kioti RX6020

Reviews:

Related manuals for Kioti RX6020

Brands by name

Popular brands

Daedong Kioti RX6020, Manual

Search results

Summary of Contents for Kioti RX6020

Reviews:

Related manuals for Kioti RX6020

Brands by name

Popular brands