Daedong Kioti RX6020 Manual Download

Page: 201 / 262

maintenance

(1) radiator screen

(2) Bolt

(a) Detach

ClEANING GRIll, RADIATOR sCREEN (G)

1. check front grill and side screens

to be sure they are clean of debris.

2. lift out the radiator screen and re-

move all the foreign material.

To avoid accidents:

Be sure to stop the engine be

fore removing the screen.

•

CAUTION

Bonnet Grill and screen must

be clean from debris to pre

vent engine from overheating

and to allow good air intake

for the air cleaner.

•

IMPORTANT

ChECkING BRAkE AND ClUTCh

PEDALS (H)

1. the brake and clutch pedals

should be inspected for free travel,

and smooth operation.

2. you should adjust these pedals

if an incorrect measurement is

found. (see maintenance code "o"

and "r" in this chapter)



when depressing the brake ped-

als separated, both of the brake

pedals should be moved down to

the same depth.

NOTE

T11O705A

TF110(RX7320)ROPS합본-US,EU,AU-07.13 13

2016-05-10 오전 8:50:46

Summary of Contents for Kioti RX6020







































































































































































































































































Search results

Summary of Contents for Kioti RX6020

Reviews:

Related manuals for Kioti RX6020

Brands by name

Popular brands

Daedong Kioti RX6020, Manual

Search results

Summary of Contents for Kioti RX6020

Reviews:

Related manuals for Kioti RX6020

Brands by name

Popular brands