Daedong Kioti RX6020 Manual Download

Page: 92 / 262

rx6020 / rx6620 / rx7320 / rx7620

hEAD lIGhT hIGh bEAM lAMP

this lamp comes on in blue when the

high beam head light is switched on.
driving with high beam head light

disturbs an approaching vehicle’

s visibility. For safe driving, use the

high beam head light only if neces-

sary.

T11O470A

T11O469A

bATTERY ChARGING lAMP

this lamp is turned on when the

starting switch is turned on before

starting the engine but turned off af-

ter starting the engine.



If this warning lamp comes

on while driving, the charging

system, such as the alternator,

is malfunctioning. Therefore,

turn off all electrical devices

and have the tractor checked

by your local KIOTI Dealer or

workshop as soon as possible.

CAUTION

TuRN SIGNAl lAMP

operating the turn signal lamp switch

up and down turns on the corre-

sponding lamp in green.

T11O468A

TF110(RX7320)ROPS합본-US,EU,AU-04.20 20

2016-06-07 오후 7:17:27

Summary of Contents for Kioti RX6020







































































































































































































































































Search results

Summary of Contents for Kioti RX6020

Reviews:

Related manuals for Kioti RX6020

Brands by name

Popular brands

Daedong Kioti RX6020, Manual

Search results

Summary of Contents for Kioti RX6020

Reviews:

Related manuals for Kioti RX6020

Brands by name

Popular brands