Daedong Kioti RX6020 Manual Download

Page: 98 / 262

rx6020 / rx6620 / rx7320 / rx7620

this lamp on when it is on regenera-

tion in dpF.

REGENERATION uNDERwAY lAMP

T11O486A

this lamp on when any major electric

device or engine fuel system is mal-

functioning.

ENGINE ChECK wARNING lAMP

T11O487A



wARNING

when on regeneration, Don’t

touch the part of DPF because

it is very hot around DPF.

•

wARNING

if carbon is accumulated in the ex-

haust catalytic filter, the warning

lamp comes on or blinks.
if this lamp comes up, push down the

"regeneration" button. (refer to the

page 4-13)

T11O485A

REGENERATION wARNING lAMP

TF110(RX7320)ROPS합본-US,EU,AU-04.26 26

2016-06-07 오후 7:17:32

Summary of Contents for Kioti RX6020







































































































































































































































































Search results

Summary of Contents for Kioti RX6020

Reviews:

Related manuals for Kioti RX6020

Brands by name

Popular brands

Daedong Kioti RX6020, Manual

Search results

Summary of Contents for Kioti RX6020

Reviews:

Related manuals for Kioti RX6020

Brands by name

Popular brands