Daedong Kioti RX6020 Manual Download Page 164

Page: 164 / 262

RX6020 / RX6620 / RX7320 / RX7620

7. The lower limit of the implement’

s height can be set by limiting the

(1) lowering Speed Control knob

(A) High Speed

(B) low Speed

M55O560A

6. The lowering speed of the lower

link is proportional to the applied

weight but can be controlled by ad-

justing the draining passage of the

hydraulic fluid. (See "lifting arm

speed control knob" on page 4-32)

T11O452A

(1) position Control lever

(2) lock Bolt

(3) lower link

(A) lifting

(B) lowering



If trying to lift an object with

e x c e s s i v e w e i g h t b y t h e

3-point hitch while the tractor

is not equipped with proper

front suit case weights, the

front wheels may be lifted

instead, leading to roll over.

Make sure to follow the speci-

fications for use.

WARNING

movement of the control lever us-

ing the stop bolt.

TF110(RX7320)ROPS합본-US,EU,AU-05.24 24

2016-06-07 오후 7:20:35

Summary of Contents for Kioti RX6020







































































































































































































































































Search results

Summary of Contents for Kioti RX6020

Reviews:

Daedong Kioti RX6020, Manual, Page: 164 / 262

Search results

Summary of Contents for Kioti RX6020

Reviews: