Daedong Kioti RX6020 Manual Download

Page: 95 / 262

description oF operating system

4wD INDICATOR

this comes on to indicate 4wd en-

gagement.
the 4wd indicator is turned off tem-

porarily while the quick turn mode is

in operation.

T11O476A

The durability of the axle can be

deteriorated if only one brake

pedal is depressed while the

4wD is activated.

•

CAuTION

if the shuttle lever is in neutral posi-

tion, this lamp turns in green.

NEuTRAl INDICATOR

T11O478A

if the shuttle lever is in forward posi-

tion, this lamp turns in green.

FORwARD INDICATOR

T11O477A

TF110(RX7320)ROPS합본-US,EU,AU-04.23 23

2016-06-07 오후 7:17:29

Summary of Contents for Kioti RX6020







































































































































































































































































Search results

Summary of Contents for Kioti RX6020

Reviews:

Related manuals for Kioti RX6020

Brands by name

Popular brands

Daedong Kioti RX6020, Manual

Search results

Summary of Contents for Kioti RX6020

Reviews:

Related manuals for Kioti RX6020

Brands by name

Popular brands