Daedong Kioti RX6020 Manual Download

Page: 114 / 262

rx6020 / rx6620 / rx7320 / rx7620

this joystick lever is used mainly to

operate the front end loader when at-

tached to the tractor.
For detailed information, refer to

"handling loader" in chapter 6.

(1) joystick lever

M55O4S4A

jOYSTICK lEvER

the lever into the "shallow" position

to activate the draft function at light

load.
For detailed information, refer to

"draft control" in chapter 5.

(1) draft control lever

(a) lifting

(b) lowering

the draft function can be used for

the plow which is installed to the

lower link (lifting arm).
if the plow is operated with excessive

draft, the lifting arm is automatically

raised to reduce the draft and then

returned to its original. this is called;

"draft Function". the plowing depth

can be controlled by the soil status

by putting the draft control lever into

the "deep" position to activate the

draft function at mid load and putting

DRAFT CONTROl lEvER

T11O453A

CAbIN

TF110(RX7320)ROPS합본-US,EU,AU-04.42 42

2016-06-07 오후 7:17:44

Summary of Contents for Kioti RX6020







































































































































































































































































Search results

Summary of Contents for Kioti RX6020

Reviews:

Related manuals for Kioti RX6020

Brands by name

Popular brands

Daedong Kioti RX6020, Manual

Search results

Summary of Contents for Kioti RX6020

Reviews:

Related manuals for Kioti RX6020

Brands by name

Popular brands