Daedong Kioti RX6020 Manual Download

Page: 110 / 262

rx6020 / rx6620 / rx7320 / rx7620

M55O4M3A

DIFFERENTIAl lOCK PEDAl

(1) lock pedal

(a) release to "disengage"

(b) depress to "engage"

the differential lock is to secure the

differential system and keep the

wheel rotation on both sides the

same in order to enhance the trac-

tion of the rear axle.
depressing the pedal engages the

differential lock while releasing the

pedal disengages the differential

lock.
Use this system under the following

conditions:

1. when any wheel slips and the

tractor does not move in the field.

2. when it is hard to break away

from a soft or muddy field.

The differential lock should be

engaged only while the driving

clutch is engaged. If the differ-

ential lock pedal does not move

when depressing it, try to de-

press it again after releasing it.
when engaging the differential

lock, reduce the engine speed.

After engaging it, accelerate

the tractor.
Make sure to set the steering

wheel in the straight ahead po-

sition while the differential lock

is in use. Otherwise, the differ-

ential system can be damaged.

•

CAuTION

(1) seat adjustment lever

M55O4M4A

SEAT ADjuSTMENT

SEAT SlIDING

to adjust the seat position, pull the

lever (1) up under the front of the

seat, slide the seat to the desired po-

sition, and then release the lever.

Make sure that the seat is firmly fixed

by moving it gently after adjustment.

CAbIN

TF110(RX7320)ROPS합본-US,EU,AU-04.38 38

2016-06-07 오후 7:17:41

Summary of Contents for Kioti RX6020







































































































































































































































































Search results

Summary of Contents for Kioti RX6020

Reviews:

Related manuals for Kioti RX6020

Brands by name

Popular brands

Daedong Kioti RX6020, Manual

Search results

Summary of Contents for Kioti RX6020

Reviews:

Related manuals for Kioti RX6020

Brands by name

Popular brands