manualshive.com logo in svg

Daedong Kioti RX6020, Manual, Page: 206 / 262

Share
Download
Daedong Kioti RX6020 Manual Download Page 206

7

-

1

rx6020 / rx6620 / rx7320 / rx7620

(1)  Drain plug 

  (2) air Bleeding plug

ChANGING fRONT AxlE CAsE OIl (N)

1. to  drain  the  used  oil,  remove  the 

right  and  left  drain  plugs  and  fill-

ing plug at the front axle case and 

drain the oil completely into the oil 

pan.

2. after  draining,  reinstall  the  drain 

plugs securely.

3. remove the oil level checking plug 

on the left of the front axle.

(1) oil filler plug

INSPECTION FRONT AxLE CASE 

OIl (N1)

1. remove  the  filling  plug  from  the 

front axle.

2. check  the  oil  level  with  the  level 

gauge of the filler plug.

3. if the oil level is too low, add new 

oil to the allowable level.

M55O757A

Oil Capacity 

2.2 u.s.gal. (8.5 l)

4. Add  new  oil  to  the  specified  level  

through the oil filler. 

5. wait  at  least  15  minutes  to  allow 

the  oil  flow  to  the  bevel  case  be-

fore checking the oil level .

6. add  oil  as  necessary  and  tighten 

the  oil  filler  plugs  and  oil  level 

checking plug.

T11O749A

TF110(RX7320)ROPS합본-US,EU,AU-07.18   18

2016-05-10   오전 8:50:48

Summary of Contents for Kioti RX6020







































































































































































































































































Reviews:

No comments