Daedong Kioti RX6020 Manual Download

Page: 103 / 262

description oF operating system

(1) main shift lever

M55O4E2A

MAIN ShIFT lEvER

Four speeds can be selected by

moving this main shift lever in the

「

」

shaped path. it is possible to

shift this lever from the 1st to 4th

gears even when the tractor is mov-

ing by disengaging the clutch as

these gears are synchromeshed.

there are 4 speeds for the main shift

lever, 3 speeds for the range shift

lever and 2 directions for the shuttle

shift lever. therefore, there are 12

forward driving speeds and 12 re-

verse driving speeds in total.

RANGE GEAR ShIFT lEvER

M55O4E3A

3 speeds can be selected by oper-

ating the range gear shift lever in

the

「I」

shaped pattern.

Only shift

this lever after the tractor is com-

pletely stopped by depressing

the clutch pedal.

if the lever does

not move freely or makes abnormal

noise, put the lever in the neutral po-

sition, depress the clutch pedal, and

then try to shift the lever.

(1) range gear shift lever (3 speeds)

(l) low speed

(n) neutral

(m) middle speed

(h) high speed

T11O411B

(1) range gear shift lever (6 speeds)

(l) low speed

(n) neutral

(m1) middle speed 1

(m2) middle speed 2 (h) high speed

(d) drive

6 speeds can be selected by oper-

ating the range gear shift lever in

the

「」

shaped pattern.

Only shift

this lever after the tractor is com-

pletely stopped by depressing

the clutch pedal.

if the lever does

not move freely or makes abnormal

noise, put the lever in the neutral po-

sition, depress the clutch pedal, and

then try to shift the lever.

TF110(RX7320)ROPS합본-US,EU,AU-04.31 31

2016-06-07 오후 7:17:36

Summary of Contents for Kioti RX6020







































































































































































































































































Search results

Summary of Contents for Kioti RX6020

Reviews:

Related manuals for Kioti RX6020

Brands by name

Popular brands

Daedong Kioti RX6020, Manual

Search results

Summary of Contents for Kioti RX6020

Reviews:

Related manuals for Kioti RX6020

Brands by name

Popular brands