Daedong Kioti RX6020 Manual Download Page 29

Page: 29 / 262

safetY precautions

1. never let anyone get in the loader

and use the loader as a worksta-

tion. otherwise, it may lead to a

fatal injury or even death.

H11O102a

safety Precautions when using the loader

2. do not stand under the lifted loader

or get close to it. also, lower the

loader arm onto the ground before

leaving the tractor. otherwise, it

may lead to a fatal injury or even

death. use the safety bar to prop

up the loader.

H11O103a

3. the loader can be turned over if a

draw-bar is improperly loaded.

make sure to use a draw-bar prop-

er for the 3-point hitch lower link.

otherwise, it may lead to an injury

or even death.

H11O104a

TF110(RX7320)ROPS합본-US,EU,AU-01.17 17

2016-06-07 오후 7:07:01

Summary of Contents for Kioti RX6020







































































































































































































































































Search results

Summary of Contents for Kioti RX6020

Reviews:

Daedong Kioti RX6020, Manual, Page: 29 / 262

Search results

Summary of Contents for Kioti RX6020

Reviews: