Daedong Kioti RX6020 Manual Download Page 168

Page: 168 / 262

RX6020 / RX6620 / RX7320 / RX7620

This tractor is equipped with the

remote control valve of the double

acting type. However, this valve can

also be used in the single acting type

hydraulic cylinder.
1. Connect one end of the hydraulic

port to the single acting cylinder as

shown in the figure. The hydraulic

pressure is properly supplied to the

cylinder. However, when the hydrau-

lic pressure is released, the cylinder

is contracted only if there is outer

force, such as potential energy.

SINGLE ACTING AND DOUBLE ACTING CYLINDER

(1) Single Acting Cylinder

(A) External load

H11O585A

2. To contract the cylinder, operate

the lever to the opposite direc-

tion of the expansion. Then, the

hydraulic fluid is supplied from the

hydraulic pump to the hydraulic

port which is not connected, and

the pressure rises as the port is

blocked. However, this pressure is

released as the relief valve opens.

3. When the cylinder is contracted,

the hydraulic fluid returned from

the cylinder is drained to the trans-

mission through the draining circuit

(2) double Acting Cylinder

m55o526A

as the operating lever is operated

to the opposite direction from the

expansion position.

It is recommended to use the

double acting cylinder instead

of the single acting cylinder if

the implement will be operated

frequently and continuously.

If using the single acting cyl-

inder too frequently or for an

extended period of time, the

hydraulic fluid can be over-

heated, resulting in deteriora-

tion of the hydraulic parts’ du-

rability as the main relief valve

opens at cylinder contraction.

•

IMPORTANT

TF110(RX7320)ROPS합본-US,EU,AU-05.28 28

2016-06-07 오후 7:20:37

Summary of Contents for Kioti RX6020







































































































































































































































































Search results

Summary of Contents for Kioti RX6020

Reviews:

Daedong Kioti RX6020, Manual, Page: 168 / 262

Search results

Summary of Contents for Kioti RX6020

Reviews: