Daedong Kioti RX6020 Manual Download Page 214

Page: 214 / 262

rx6020 / rx6620 / rx7320 / rx7620

(1) adjusting Bolt

(a) adjusting Belt tension

(B) pull

ADJUsTING fAN BElT TENsION (V)

in order to extend the fan belt life-

time, the tension of the belt should be

correctly adjusted. the belt tension

should be inspected regularly accord-

ing to the following procedure:
1. stop the engine and apply the

parking brake.

2. open the hood.
3. apply moderate thumb pressure

to the belt (a) between the crank-

shaft pulley and alternator pulley

to check for tension.

To avoid personal injury:

Be sure to stop the engine be

fore checking belt tension.

•

CAUTION

when changing fuel pipes, be

careful not to allow dust or dirt

to enter the fuel system. Con-

taminations in the fuel system

could damage the fuel system

or injection pump. Pay extra

caution to the fuel pump to

prevent dust from entering it.

•

IMPORTANT

4. if tension is incorrect, loosen the

alternator mounting bolt and hinge

bolt. pull the alternator outward

using a pry bar to reach the proper

belt tension.

5. Be sure to retighten the alternator

mounting bolt and hinge bolt se-

curely after adjusting belt tension.

6. replace the fan belt if it is dam-

aged, cracked or worn.

Belt deflection for proper

fan belt tension (A)

0.39 ~ 0.47 in. (10 ~12 mm)

T11O713A

TF110(RX7320)ROPS합본-US,EU,AU-07.26 26

2016-05-10 오전 8:50:54

Summary of Contents for Kioti RX6020







































































































































































































































































Search results

Summary of Contents for Kioti RX6020

Reviews:

Daedong Kioti RX6020, Manual, Page: 214 / 262

Search results

Summary of Contents for Kioti RX6020

Reviews: