Daedong Kioti RX6020 Manual Download Page 108

Page: 108 / 262

rx6020 / rx6620 / rx7320 / rx7620

PARKING bRAKE lEvER

(1) parking brake lever (2) brake pedals

(3) pedal interlock

(a) depressing

(b) pressing down

M55O4M1A



If the vehicle is driven with the

parking brake partially or com-

pletely engaged, it may cause

early wear of the brake disc.



If the indicator is ON even with

the parking brake released,

have the tractor checked by

your local KIOTI dealer or

workshop immediately.

CAuTION

to stop the tractor, depress the brake

pedal and pull the lever up to apply

To avoid possible injury, death

or loss of property from a ma-

chine runaway



with the engine off, the tractor

may move unexpectedly re-

gardless of the gear shift posi-

tion.



before leaving the tractor,

firmly apply the parking brake

to prevent machine runaway.

※

Only power shuttle model.

wARNING

the parking brake. (Usa/aU only)
to stop the tractor, depress the

brake pedal and pull the lever up to

apply the parking brake. to engage

the parking brake, pull the lever up.

to release the parking brake, pull up

and press the thumb button. then,

while holding the button in, lower the

brake lever. (eU only)

TF110(RX7320)ROPS합본-US,EU,AU-04.36 36

2016-06-07 오후 7:17:39

Summary of Contents for Kioti RX6020







































































































































































































































































Search results

Summary of Contents for Kioti RX6020

Reviews:

Daedong Kioti RX6020, Manual, Page: 108 / 262

Search results

Summary of Contents for Kioti RX6020

Reviews: