Daedong Kioti RX6020 Manual Download

Page: 111 / 262

description oF operating system

the seat height can be adjusted to

fit to the driver. turning the handle

(1) on the front of the seat clockwise

raises the seat while turning it coun-

terclockwise lowers the seat.

(1) seat height adjustment handle

M55O4M6A

SEAT hEIGhT ADjuSTMENT

SEAT bACK REClINING

(1) seat back adjustment lever

M55O4M5A

to change the seat back angle, raise

the lever (1) on the left of the seat.

then, adjust the seat back angle

with the lever pulled. release the le-

ver after adjustment. make sure that

the lever is returned and the seat is

firmly fixed after adjustment.

Do not put a hand between the

seat and the slides when ad-

justing the seat position. You

can be injured unexpectedly.

•

CAuTION

T11O4A41

(1) seat adjustment lever

ROPS

TF110(RX7320)ROPS합본-US,EU,AU-04.39 39

2016-06-07 오후 7:17:42

Summary of Contents for Kioti RX6020







































































































































































































































































Search results

Summary of Contents for Kioti RX6020

Reviews:

Related manuals for Kioti RX6020

Brands by name

Popular brands

Daedong Kioti RX6020, Manual

Search results

Summary of Contents for Kioti RX6020

Reviews:

Related manuals for Kioti RX6020

Brands by name

Popular brands