Daedong Kioti RX6020 Manual Download

Page: 86 / 262

rx6020 / rx6620 / rx7320 / rx7620

CluTCh PEDAl ENGAGEMENT CONTROl buTTON

T11O4A31

(a) Fast

(b) slow

the engagement height of the clutch

pedal can be adjusted with this button

and this function is only available for

the power shuttle model.
pressing the upper portion of the but-

ton speeds up the clutch engagement

operation while pressing its lower por-

tion slows down the clutch engagement

operation.

6. the regeneration underway lamp

blinks after the regeneration warning

lamp goes off.

wait for approx. 30 to 40 minutes

until the regeneration process is

completed.

DEACTIvATION (lOwER buTTON)

do not press the deactivation button

during the regeneration process.
however, in an emergency, press

the deactivation button to stop the

regeneration process.

T11O4A52

(1) dpF regeneration switch

(a) activation

(b) deactivation

ROPS

T11O4A31

(a) Fast

(b) slow

CAbIN

ROPS

TF110(RX7320)ROPS합본-US,EU,AU-04.14 14

2016-06-07 오후 7:17:23

Summary of Contents for Kioti RX6020







































































































































































































































































Search results

Summary of Contents for Kioti RX6020

Reviews:

Related manuals for Kioti RX6020

Brands by name

Popular brands

Daedong Kioti RX6020, Manual

Search results

Summary of Contents for Kioti RX6020

Reviews:

Related manuals for Kioti RX6020

Brands by name

Popular brands