Home
/
Chrysler
/
300 Touring RWD 2010
/
Owner'S Manual

Chrysler 300 Touring RWD 2010, Owner'S Manual

Share

Page: 93 / 574

Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 93

strap. See the section “Installing Child Restraints

Using the Top Tether Anchorage” for directions to

attach a tether anchor.

9. Test that the child restraint is installed tightly by

pulling back and forth on the child seat at the belt

path. It should not move more than 1 inch (25.4 mm)

in any direction.

Any seat belt system will loosen with time, so check the

seat belt occasionally, and pull it tight if necessary.

Installing Child Restraints Using The Top Tether
Anchorage

WARNING!

Do not attach a tether strap for a rear-facing car seat
to any location in front of the car seat, including the
seat frame or a tether anchorage. Only attach the

(Continued)

WARNING!

(Continued)

tether strap of a rear-facing car seat to the tether
anchorage that is approved for that seating position,
located behind the top of the vehicle seat. See the
section “Lower Anchors and Tethers for CHildren
(LATCH) Restraint System” for the location of ap-
proved tether anchorages in your vehicle.

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91

«
...
91
92
93
94
95
...
»

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands