Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 274

Page: 274 / 574

DRIVER INFORMATION DISPLAY (DID)

The Driver Information Display (DID) features an inter-

active display which is located in the instrument cluster.
This system conveniently allows the driver to select a

variety of useful information by pushing the arrow

buttons located on the left side of the steering wheel. The

DID Menu Items consists of the following:

•

Speedometer

•

Vehicle Info

•

Driver Assist — If Equipped

•

Fuel Economy

•

Trip

•

Audio

•

Messages

•

Screen Setup

The system allows the driver to select information by

pushing the following buttons mounted on the steering

wheel:

DID Controls

272 UNDERSTANDING YOUR INSTRUMENT PANEL

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands

Chrysler 300 Touring RWD 2010, Owner'S Manual

Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands