manualshive.com logo in svg

Chrysler 300 Touring RWD 2010, Owner'S Manual

Share
Download
Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 68

continues, see your doctor. If these particles settle on

your clothing, follow the garment manufacturer’s in-

structions for cleaning.

Do not drive your vehicle after the air bags have de-

ployed. If you are involved in another collision, the air

bags will not be in place to protect you.

WARNING!

Deployed air bags and seat belt pretensioners cannot
protect you in another collision. Have the air bags,
seat belt pretensioners, and the seat belt retractor
assemblies replaced by an authorized dealer imme-
diately. Also, have the Occupant Restraint Controller
System serviced as well.

NOTE:

•

Air bag covers may not be obvious in the interior trim,

but they will open during air bag deployment.

•

After any collision, the vehicle should be taken to an

authorized dealer immediately.

Enhanced Accident Response System

In the event of an impact, if the communication network

remains intact, and the power remains intact, depending

on the nature of the event, the ORC will determine

whether to have the Enhanced Accident Response Sys-

tem perform the following functions:

•

Cut off fuel to the engine.

•

Flash hazard lights as long as the battery has power or

until the ignition switch is turned to the “OFF” posi-

tion.

66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands