manualshive.com logo in svg

Chrysler 300 Touring RWD 2010, Owner'S Manual

Share
Download
Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 548

Call toll free at:

•

1-800-890-4038 (U.S.)

•

1-800-387-1143 (Canada)

Or
Visit us on the Worldwide Web at:

•

www.techauthority.com

DEPARTMENT OF TRANSPORTATION UNIFORM
TIRE QUALITY GRADES

The following tire grading categories were established by

the National Highway Traffic Safety Administration. The

specific grade rating assigned by the tire’s manufacturer

in each category is shown on the sidewall of the tires on

your vehicle.
All passenger car tires must conform to Federal safety

requirements in addition to these grades.

Treadwear

The Treadwear grade is a comparative rating, based on

the wear rate of the tire when tested under controlled

conditions on a specified government test course. For

example, a tire graded 150 would wear one and one-half

times as well on the government course as a tire graded

100. The relative performance of tires depends upon the

actual conditions of their use, however, and may depart

significantly from the norm due to variations in driving

habits, service practices, and differences in road charac-

teristics and climate.

Traction Grades

The Traction grades, from highest to lowest, are AA, A, B,

and C. These grades represent the tire’s ability to stop on

wet pavement, as measured under controlled conditions

on specified government test surfaces of asphalt and

concrete. A tire marked C may have poor traction perfor-

mance.

546 IF YOU NEED CONSUMER ASSISTANCE

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands