manualshive.com logo in svg

Chrysler 300 Touring RWD 2010, Owner'S Manual

Share
Download
Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 142

DRIVER MEMORY SEAT — IF EQUIPPED

This feature allows the driver to store up to two different

memory profiles for easy recall through a memory

switch. Each memory profile contains desired position

settings for the driver seat, side mirrors, adjustable

pedals (if equipped), and power tilt and telescopic steer-

ing column (if equipped) and a set of desired radio

station presets. Your Remote Keyless Entry (RKE) trans-

mitter can also be programmed to recall the same posi-

tions when the UNLOCK button is pushed.

NOTE:

•

Only one RKE transmitter can be linked to each of the

memory positions.

•

Passive Entry door handles cannot be linked to the

memory function. Use either the memory recall switch

or the RKE transmitter (if linked to the memory

feature) to recall memory positions 1 or 2.

The memory seat switch is located on the driver’s door

trim panel. The switch consists of three buttons: The (S)

button, which is used to activate the memory save

function and the (1) and (2) buttons which are used to

recall either of two pre-programmed memory profiles.

Memory Seat Switch

140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands