Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 482

Page: 482 / 574

Lubricants that do not have both, the engine oil certifi-

cation mark and the correct SAE viscosity grade number

should not be used.

Synthetic Engine Oils

You may use synthetic engine oils provided the recom-

mended oil quality requirements are met, and the recom-

mended maintenance intervals for oil and filter changes

are followed.

Materials Added To Engine Oil

The manufacturer strongly recommends against the ad-

dition of any additives (other than leak detection dyes) to

the engine oil. Engine oil is an engineered product and its

performance may be impaired by supplemental addi-

tives.

Disposing Of Used Engine Oil And Oil Filters

Care should be taken in disposing of used engine oil and

oil filters from your vehicle. Used oil and oil filters,

indiscriminately discarded, can present a problem to the

environment. Contact your authorized dealer, service

station or governmental agency for advice on how and

where used oil and oil filters can be safely discarded in

your area.

Engine Oil Filter

The engine oil filter should be replaced with a new filter

at every engine oil change.

Engine Oil Filter Selection

This manufacturer’s engines have a full-flow type oil

filter. Use a filter of this type for replacement. The quality

of replacement filters varies considerably. Only high

quality filters should be used to assure most efficient

service. MOPAR® engine oil filters are a high quality oil

filter and are recommended.

480 MAINTAINING YOUR VEHICLE

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands

Chrysler 300 Touring RWD 2010, Owner'S Manual

Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands