manualshive.com logo in svg

Chrysler 300 Touring RWD 2010, Owner'S Manual

Share
Download
Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 254

Rear Seat Armrest Storage — If Equipped

For rear passengers there is a storage bin located in the

armrest. Lift upward on the latch to open the storage

compartment.

Cargo Area — Vehicles Equipped With 60/40
Split-Folding Rear Seat

The 60/40 split-folding rear seat provides cargo-carrying

versatility. The seatbacks fold down easily by pulling

nylon tabs between the seatbacks and the bolsters. When

the seats are folded down, they provide a continuous,

nearly-flat extension of the load floor.
When the seatback is folded to the upright position, make

sure it is latched by strongly pulling on the top of the

seatback above the seat strap.

Rear Armrest Storage

252 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands