manualshive.com logo in svg

Chrysler 300 Touring RWD 2010, Owner'S Manual

Share
Download
Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 448

WARNING!

(Continued)

•

The jack is designed to be used as a tool for
changing tires only. The jack should not be used to
lift the vehicle for service purposes. The vehicle
should be jacked on a firm level surface only.
Avoid ice or slippery areas.

Jack Location/Spare Tire Stowage

The jack and spare tire are both stowed under an access

cover in the trunk. Follow these steps to access the jack

and spare tire.

NOTE:

The spare tire must be removed in order to

access the jack.
1. Open the trunk.
2. Lift the access cover using the pull strap.

3. Remove the fastener securing the spare tire.

Opening The Access Panel

446 WHAT TO DO IN EMERGENCIES

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands