manualshive.com logo in svg

Chrysler 300 Touring RWD 2010, Owner'S Manual

Share
Download
Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 121

The area on the rear fascia where the radar sensors are

located must remain free of snow, ice, and dirt/road

contamination so that the BSM system can function

properly. Do not block the area of the rear fascia where

the radar sensors are located with foreign objects (bum-

per stickers, bicycle racks, etc.).

The BSM system notifies the driver of objects in the

detection zones by illuminating the BSM warning light

located in the outside mirrors in addition to sounding an

audible (chime) alert and reducing the radio volume.

Refer to “Modes Of Operation” for further information.
The BSM system monitors the detection zone from three

different entry points (side, rear, front) while driving to

see if an alert is necessary. The BSM system will issue an

alert during these types of zone entries.

Sensor Location (Driver Side Shown)

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands