manualshive.com logo in svg

Chrysler 300 Touring RWD 2010, Owner'S Manual

Share
Download
Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 279

SETTING THE ANALOG CLOCK

To set the analog clock at the top center of the instrument

panel, push and hold the button until the setting is

correct.

Uconnect® SETTINGS

The Uconnect® system uses a combination of buttons on

the touchscreen and buttons on the faceplate located on

the center of the instrument panel that allows you to

access and change the customer programmable features.

CAUTION!

Do NOT attach any object to the touchscreen, doing
so can result in damage to the touchscreen.

Setting The Analog Clock

4

UNDERSTANDING YOUR INSTRUMENT PANEL 277

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands