Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 363

Page: 363 / 574

PARKING BRAKE

Before leaving the vehicle, make sure that the parking

brake is fully applied and place the shift lever/gear

selector in the PARK position.
The foot operated parking brake is located below the

lower left corner of the instrument panel. To apply the

park brake, firmly push the park brake pedal fully. To

release the parking brake, press the park brake pedal a

second time and let your foot up as you feel the brake

disengage.

When the parking brake is applied with the ignition

switch in the ON position, the “Brake Warning Light” in

the instrument cluster will illuminate.

Parking Brake

STARTING AND OPERATING 361

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands

Chrysler 300 Touring RWD 2010, Owner'S Manual

Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands