manualshive.com logo in svg

Chrysler 300 Touring RWD 2010, Owner'S Manual

Share
Download
Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 167

NOTE:

The engine must be running for the heated

steering wheel to operate.

Vehicles Equipped With Remote Start

On models that are equipped with remote start, the

heated steering wheel can be programmed to come on

during a remote start through the Uconnect® system.

Refer to “Uconnect® Settings” in “Understanding Your

Instrument Panel” for further information.

WARNING!

•

Persons who are unable to feel pain to the skin
because of advanced age, chronic illness, diabetes,
spinal cord injury, medication, alcohol use, exhaus-
tion, or other physical conditions must exercise
care when using the steering wheel heater. It may
cause burns even at low temperatures, especially if
used for long periods.

•

Do not place anything on the steering wheel that
insulates against heat, such as a blanket or steering
wheel covers of any type and material. This may
cause the steering wheel heater to overheat.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands