manualshive.com logo in svg

Chrysler 300 Touring RWD 2010, Owner'S Manual

Share
Download
Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 37

To Enter The Trunk

With a valid Passive Entry RKE transmitter within 3 ft

(1.0 m) of the deck lid, push the button on the right side

of CHMSL (Center High Mounted Stop Light), which is

located on the deck lid.

NOTE:

If you inadvertently leave your vehicle’s Passive

Entry RKE transmitter in the trunk and try to close the deck

lid, the deck lid will automatically unlatch, unless another

one of the vehicle’s Passive Entry RKE transmitters is

outside the vehicle and within 3 ft (1.0 m) of the deck lid.

Trunk Passive Entry Button

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands