Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 495

Page: 495 / 574

miles (240,000 km) before replacement. To prevent reduc-

ing this extended maintenance period, it is important that

you use the same engine coolant (OAT coolant conform-

ing to MS.90032) throughout the life of your vehicle.
Please review these recommendations for using Organic

Additive Technology (OAT) engine coolant (antifreeze)

that meets the requirements of Chrysler Material Stan-

dard MS.90032. When adding engine coolant (antifreeze):

•

We recommend using MOPAR® Antifreeze/Coolant

10 Year/150,000 Mile Formula OAT (Organic Additive

Technology) that meets the requirements of Chrysler

Material Standard MS.90032.

•

Mix a minimum solution of 50% OAT engine coolant

that meets the requirements of Chrysler Material Stan-

dard MS.90032 and distilled water. Use higher concen-

trations (not to exceed 70%) if temperatures below

−

34° F (

−

37° C) are anticipated.

•

Use only high purity water such as distilled or deion-

ized water when mixing the water/engine coolant

(antifreeze) solution. The use of lower quality water

will reduce the amount of corrosion protection in the

engine cooling system.

Please note that it is the owner’s responsibility to main-

tain the proper level of protection against freezing ac-

cording to the temperatures occurring in the area where

the vehicle is operated.

MAINTAINING YOUR VEHICLE 493

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands

Chrysler 300 Touring RWD 2010, Owner'S Manual

Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands