Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 386

Page: 386 / 574

NOTE:

Under a maximum loaded vehicle condition,

gross axle weight ratings (GAWRs) for the front and rear

axles must not be exceeded. For further information on

GAWRs, vehicle loading, and trailer towing, refer to

“Vehicle Loading” in this section.
To determine the maximum loading conditions of your

vehicle, locate the statement “The combined weight of

occupants and cargo should never exceed XXX lbs or

XXX kg” on the Tire and Loading Information placard.

The combined weight of occupants, cargo/luggage and

trailer tongue weight (if applicable) should never exceed

the weight referenced here.

Steps For Determining Correct Load Limit

1. Locate the statement “The combined weight of occu-

pants and cargo should never exceed XXX lbs or

XXX kg” on your vehicle’s placard.

2. Determine the combined weight of the driver and

passengers that will be riding in your vehicle.

3. Subtract the combined weight of the driver and pas-

sengers from XXX lbs or XXX kg.

384 STARTING AND OPERATING

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands

Chrysler 300 Touring RWD 2010, Owner'S Manual

Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands