Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 228

Page: 228 / 574

OVERHEAD CONSOLE

The overhead console contains courtesy/reading lights

and storage for sunglasses. Universal Garage Door

Opener (HomeLink®) and power sunroof switches may

also be included, if equipped.

Front Map/Reading Lights — If Equipped

Lights are mounted in the overhead console. Each light

can be turned on by pushing the switch on either side of

the console. These buttons are backlit for night time

visibility.

Overhead Console

Front Map/Reading Lights

226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands

Chrysler 300 Touring RWD 2010, Owner'S Manual

Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands