manualshive.com logo in svg

Chrysler 300 Touring RWD 2010, Owner'S Manual

Share
Download
Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 169

Push the switch rearward to move the pedals rearward

(toward the driver).

•

The pedals can be adjusted with the ignition OFF.

•

The pedals

cannot

be adjusted when the vehicle is in

REVERSE or when the Electronic Speed Control Sys-

tem is on. The following messages will be displayed on

vehicles equipped with the Driver Information Dis-

play (DID) if the pedals are attempted to be adjusted

when the system is locked out (“Adjustable Pedal

Disabled — Cruise Control Engaged” or “Adjustable

Pedal Disabled — Vehicle In Reverse”).

NOTE:

•

Always adjust the pedals to a position that allows full

pedal travel.

•

Further small adjustments may be necessary to find

the best possible seat/pedal position.

•

For vehicles equipped with Driver Memory Seat, you

can use your Remote Keyless Entry (RKE) transmitter

or the memory switch on the driver’s door trim panel

to return the adjustable pedals to pre-programmed

positions. Refer to “Driver Memory Seat” in “Under-

standing The Features Of Your Vehicle” for further

information.

CAUTION!

Do not place any article under the adjustable pedals
or impede its ability to move as it may cause damage
to the pedal controls. Pedal travel may become lim-
ited if movement is stopped by an obstruction in the
adjustable pedal’s path.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands