Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 466

Page: 466 / 574

Towing

Condition

Wheels OFF The Ground

RWD MODELS

AWD MODELS

Flat Tow

NONE

If transmission is operable:

•

Transmission in

NEUTRAL

•

30 mph (48 km/h)

max

speed

•

30 miles (48 km)

max

distance

NOT ALLOWED

Wheel Lift or

Dolly Tow

Front

NOT RECOMMENDED

(but, if used, same limita-

tions as above)

NOT ALLOWED

Rear

NOT RECOMMENDED

NOT RECOMMENDED, but,

if used:

•

Ignition in ON/RUN posi-

tion

•

Transmission in

NEUTRAL

(NOT in Park)

Flatbed

ALL

BEST METHOD

464 WHAT TO DO IN EMERGENCIES

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands

Chrysler 300 Touring RWD 2010, Owner'S Manual

Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands