Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 119

Page: 119 / 574

BLIND SPOT MONITORING (BSM) — IF
EQUIPPED

The Blind Spot Monitoring (BSM) system uses two radar-

based sensors, located inside the rear bumper fascia, to

detect highway licensable vehicles (automobiles, trucks,

motorcycles, etc.) that enter the blind spot zones from the

rear/front/side of the vehicle.

When the vehicle is started, the BSM warning light will

momentarily illuminate in both outside rear view mirrors

to let the driver know that the system is operational. The

BSM system sensors operate when the vehicle is in any

forward gear or REVERSE and enters stand by mode

when the vehicle is in PARK.

Rear Detection Zones

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands

Chrysler 300 Touring RWD 2010, Owner'S Manual

Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands