Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 252

Page: 252 / 574

Inside the center console armrest, there is a removable

upper storage tray that can be slid forward/rearward on

rails for access to the lower storage area. This tray has an

integrated coin holder, along with additional area for

small items like an ipod or phone. Below the upper tray,

the lower storage compartment is made for larger items,

like CDs and tissue boxes. In addition, the 12 volt power

outlet, USB and Aux jack are located here.

Center Console

Upper Storage Tray

250 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands

Chrysler 300 Touring RWD 2010, Owner'S Manual

Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands