manualshive.com logo in svg

Chrysler 300 Touring RWD 2010, Owner'S Manual

Share
Download
Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 188

NOTE:

The “Brake!” Screen in the DID is a warning for

the driver to take action and does not necessarily mean

that the Forward Collision Warning system is applying

the brakes autonomously.

Overtake Aid

When driving with ACC engaged and following a ve-

hicle, the system will provide an additional acceleration

up to the ACC set speed to assist in passing the vehicle.

This additional acceleration is triggered when the driver

utilizes the left turn signal and will only be active when

passing on the left hand side.

ACC Operation At Stop

If the ACC system brings your vehicle to a standstill

while following a target vehicle, if the target vehicle starts

moving within two seconds of your vehicle coming to a

standstill, your vehicle will resume motion without the

need for any driver action.
If the target vehicle does not start moving within two

seconds of your vehicle coming to a standstill, the ACC

with Stop system will cancel and the brakes will release.

Brake Alert

186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands