manualshive.com logo in svg

Chrysler 300 Touring RWD 2010, Owner'S Manual

Share
Download
Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 182

NOTE:

•

If your vehicle stays at standstill for longer than two

seconds, then the system will cancel and the brake

force will be ramped-out. The driver will have to apply

the brakes to keep the vehicle at a standstill.

•

ACC cannot be resumed if there is a stationary vehicle

in-front of your vehicle in close proximity.

WARNING!

The Resume function should only be used if traffic
and road conditions permit. Resuming a set speed
that is too high or too low for prevailing traffic and
road conditions could cause the vehicle to accelerate
or decelerate too sharply for safe operation. Failure to
follow these warnings can result in a collision and
death or serious personal injury.

To Vary The Speed Setting

To Increase Speed

While ACC is set, you can increase the set speed by

pushing the SET

+

button.

The drivers preferred units can be selected through the

instrument panel settings if equipped. Refer to “Under-

standing Your Instrument Panel” for more information.

The speed increment shown is dependant on the chosen

speed unit of U.S. (mph) or Metric (km/h):

U.S. Speed (mph)

•

Pushing the SET

+

button once will result in a 1 mph

increase in set speed. Each subsequent tap of the

button results in an increase of 1 mph.

•

If the button is continually pushed, the set speed will

continue to increase in 5 mph increments until the

button is released. The increase in set speed is reflected

in the DID.

180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands