Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 256

Page: 256 / 574

CARGO AREA FEATURES

Trunk Mat — If Equipped

A trunk mat covers the bottom of the cargo area. The

trunk mat is used to protect the interior of the trunk from

mud, snow, and debris.

Grocery Bag Hooks

The rear cargo area is equipped with grocery bag hooks,

located on either side of the rear cargo area.

CAUTION!

Do not exceed the maximum weight limit 50 lbs
(22 kg) of the grocery bag hook. Damage may occur to
hook and mounting surface.

Grocery Bag Hooks

254 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands

Chrysler 300 Touring RWD 2010, Owner'S Manual

Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands