Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 168

Page: 168 / 574

ADJUSTABLE PEDALS — IF EQUIPPED

The adjustable pedals system is designed to allow a

greater range of driver comfort for steering wheel tilt and

seat position. This feature allows the brake and accelera-

tor pedals to move toward or away from the driver to

provide improved position with the steering wheel.
The switch is located on the front side of the driver’s seat

cushion side shield.

Push the switch forward to move the pedals forward

(toward the front of the vehicle).

Adjustable Pedals Switch

166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands

Chrysler 300 Touring RWD 2010, Owner'S Manual

Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands