manualshive.com logo in svg

Chrysler 300 Touring RWD 2010, Owner'S Manual

Share
Download
Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 437

CAUTION!

•

Do not tow a trailer at all during the first 500 miles
(805 km) the new vehicle is driven. The engine, axle
or other parts could be damaged.

•

Then, during the first 500 miles (805 km) that a
trailer is towed, do not drive over 50 mph (80 km/h)
and do not make starts at full throttle. This helps
the engine and other parts of the vehicle wear in at
the heavier loads.

Towing Requirements — Tires

•

Do not attempt to tow a trailer while using a compact

spare tire.

•

Proper tire inflation pressures are essential to the safe

and satisfactory operation of your vehicle. Refer to

“Tires – General Information” in “Starting And Oper-

ating” for information on tire pressures and for proper

tire inflation procedures.

•

Check the trailer tires for proper tire inflation pres-

sures before trailer usage.

•

Check for signs of tire wear or visible tire damage

before towing a trailer. Refer to “Tires – General

Information” in “Starting And Operating” for informa-

tion on tread wear indicators and for the proper

inspection procedure.

•

When replacing tires, refer to “Tires – General Infor-

mation” in “Starting And Operating” for information

on replacement tires and for the proper tire replace-

ment procedures. Replacing tires with a higher load

carrying capacity will not increase the vehicle’s GVWR

and GAWR limits.

5

STARTING AND OPERATING 435

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands