manualshive.com logo in svg

Chrysler 300 Touring RWD 2010, Owner'S Manual

Share
Download
Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 343

WARNING!

(Continued)

•

If the vehicle has a discharged battery, booster
cables may be used to obtain a start from a booster
battery or the battery in another vehicle. This type
of start can be dangerous if done improperly. Refer
to “Jump-Starting” in “What To Do In Emergen-
cies” for further information.

Clearing A Flooded Engine (Using ENGINE
START/STOP Button)

If the engine fails to start after you have followed the

“Normal Starting” or “Extreme Cold Weather

#

proce-

dures, it may be flooded. To clear any excess fuel:
1. Press and hold the brake pedal.

2. Press the accelerator pedal all the way to the floor and

hold it.

3. Push and release the ENGINE START/STOP button

once.

The starter motor will engage automatically, run for 10

seconds, and then disengage. Once this occurs, release

the accelerator pedal and the brake pedal, wait 10 to 15

seconds, then repeat the “Normal Starting” procedure.

After Starting

The idle speed is controlled automatically and it will

decrease as the engine warms up.

5

STARTING AND OPERATING 341

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands