Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 172

Page: 172 / 574

To Deactivate

A soft tap on the brake pedal, pushing the CANCEL

button, or normal brake pressure while slowing the

vehicle will deactivate the Electronic Speed Control with-

out erasing the set speed from memory.
Pushing the ON/OFF button or turning the ignition

switch OFF erases the set speed from memory.

To Resume Speed

To resume a previously set speed, push the RES (+)

button and release. Resume can be used at any speed

above 20 mph (32 km/h).

To Vary The Speed Setting

To Increase Speed

When the Electronic Speed Control is set, you can in-

crease speed by pushing the SET

button.

The drivers preferred units can be selected through the

instrument panel settings if equipped. Refer to “Under-

standing Your Instrument Panel” for more information.

The speed increment shown is dependant on the chosen

speed unit of U.S. (mph) or Metric (km/h):

U.S. Speed (mph)

•

Pushing the SET

button once will result in a 1 mph

increase in set speed. Each subsequent tap of the

button results in an increase of 1 mph.

•

If the button is continually pushed, the set speed will

continue to increase until the button is released, then

the new set speed will be established.

170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands

Chrysler 300 Touring RWD 2010, Owner'S Manual

Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands