manualshive.com logo in svg

Chrysler 300 Touring RWD 2010, Owner'S Manual

Share
Download
Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 52

5. Position the shoulder belt across the shoulder and

chest with minimal, if any slack so that it is comfort-

able and not resting on your neck. The retractor will

withdraw any slack in the shoulder belt.

6. To release the seat belt, push the red button on the

buckle. The seat belt will automatically retract to its

stowed position. If necessary, slide the latch plate

down the webbing to allow the seat belt to retract

fully.

Lap/Shoulder Belt Untwisting Procedure

Use the following procedure to untwist a twisted lap/

shoulder belt.
1. Position the latch plate as close as possible to the

anchor point.

2. At about 6 to 12 in (15 to 30 cm) above the latch plate,

grasp and twist the seat belt webbing 180 degrees to

create a fold that begins immediately above the latch

plate.

3. Slide the latch plate upward over the folded webbing.

The folded webbing must enter the slot at the top of

the latch plate.

4. Continue to slide the latch plate up until it clears the

folded webbing and the seat belt is no longer twisted.

Adjustable Upper Shoulder Belt Anchorage

In the driver and front passenger seats, the top of the

shoulder belt can be adjusted upward or downward to

position the seat belt away from your neck. Push or

squeeze the anchorage button to release the anchorage,

and move it up or down to the position that serves you

best.

50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands