Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 208

Page: 208 / 574

•

When the LaneSense system senses the lane has been

approached and is in a lane departure situation, the

left thick lane line flashes yellow (on/off), the left thin

line remains solid yellow and the LaneSense indicator

changes from solid white to flashing yellow.

NOTE:

The LaneSense system operates with the similar

behavior for a right lane departure when only the right

lane marking has been detected.

Left Lane Departure — Both Lanes Detected

•

When the LaneSense system is ON, the lane lines turn

from gray to white to indicate that both of the lane

markings have been detected. The LaneSense indicator

is solid green when both lane markings have been

detected and the system is “armed” to provide visual

warnings in the DID and a torque warning in the

steering wheel if an unintentional lane departure oc-

curs.

Lane Approached (Flashing Yellow Thick Line, Solid

Yellow Thin Line/Flashing Yellow Indicator)

206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands

Chrysler 300 Touring RWD 2010, Owner'S Manual

Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands