manualshive.com logo in svg

Chrysler 300 Touring RWD 2010, Owner'S Manual

Share
Download
Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 435

NOTE:

Remember that everything put into or on the

trailer adds to the load on your vehicle. Also, additional

factory-installed options or dealer-installed options must

be considered as part of the total load on your vehicle.

Refer to the “Tire And Loading Information” placard for

the maximum combined weight of occupants and cargo

for your vehicle.

Towing Requirements

To promote proper break-in of your new vehicle drive-

train components the following guidelines are recom-

mended:

WARNING!

Improper towing can lead to an injury collision.
Follow these guidelines to make your trailer towing
as safe as possible:

•

Make certain that the load is secured in the trailer
and it will not shift during travel. When trailering
cargo that is not fully secured, dynamic load shifts
can occur that may be difficult for the driver to
control. You could lose control of your vehicle and
have a collision.

•

When hauling cargo or towing a trailer, do not
overload your vehicle or trailer. Overloading can
cause a loss of control, poor performance, or dam-
age to brakes, axle, engine, transmission, steering,
suspension, chassis structure, or tires.

(Continued)

5

STARTING AND OPERATING 433

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands