manualshive.com logo in svg

Chrysler 300 Touring RWD 2010, Owner'S Manual

Share
Download
Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 146

TO OPEN AND CLOSE THE HOOD

Two latches must be released to open the hood.
1. Pull the hood release lever located under the left side

of the instrument panel.

2. Move to the outside of the vehicle and push the safety

catch to the left. The safety catch is located under the

center front edge of the hood.

Use the hood prop rod (if equipped) to secure the hood in

the open position.

Hood Release Lever

Hood Safety Latch

144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands