manualshive.com logo in svg

Chrysler 300 Touring RWD 2010, Owner'S Manual

Share
Download
Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 438

Towing Requirements — Trailer Brakes

•

Do

not

interconnect the hydraulic brake system or

vacuum system of your vehicle with that of the trailer.

This could cause inadequate braking and possible

personal injury.

•

An electronically actuated trailer brake controller is

required when towing a trailer with electronically

actuated brakes. When towing a trailer equipped with

a hydraulic surge actuated brake system, an electronic

brake controller is not required.

•

Trailer brakes are recommended for trailers over

1,000 lbs (454 kg) and required for trailers in excess of

2,000 lbs (907 kg).

WARNING!

•

Do not connect trailer brakes to your vehicle’s
hydraulic brake lines. It can overload your brake
system and cause it to fail. You might not have
brakes when you need them and could have a
collision.

•

Towing any trailer will increase your stopping
distance. When towing you should allow for addi-
tional space between your vehicle and the vehicle
in front of you. Failure to do so could result in a
collision.

436 STARTING AND OPERATING

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands