Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 325

Page: 325 / 574

Climate (8.4A/8.4AN)

Too hot? Too cold? Adjust vehicle temperatures hands-

free and keep everyone comfortable while you keep

moving ahead. (If vehicle is equipped with climate

control.)
Push the VR button

. After the beep, say one of the

following commands:

•

Set driver temperature to

degrees

•

Set passenger temperature to

degrees

TIP:

Voice Command for Climate may only be used to

adjust the interior temperature of your vehicle. Voice

Command will not work to adjust the heated seats or

steering wheel if equipped.

Uconnect 8.4A/8.4AN Climate

UNDERSTANDING YOUR INSTRUMENT PANEL 323

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands

Chrysler 300 Touring RWD 2010, Owner'S Manual

Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands